Magnetizing and Transporting your Guild Ball miniatures!

You've probably met someone, or at least heard of someone, who magnetizes all their models and puts them in tins for safe transport. (If you haven't, well now you have: me!).

I had a friend who magnetized an entire army, some 100+ models, spread out among 5 or more different sized tins. That example is quite dangerous though. It was quite difficult carrying all those tins, and if he ever lost balance, his whole army had the potential to be ruined.

That example is a bit atypical, and probably impractical. But for a game like Guild Ball, where you only need 6 models for a game, and maybe 8 for a tournament, or even only 11 for a full team, magnetizing may be a bit more practical.

So, you may be wondering: why magnetize? Why not just use trusty foam and carrying cases? Simple: if you transport your models and actually take them out of the case to play, scratching your sweet paint job is an eventuality.

Putting your models on the table top can lead to damage. An errant dice roll, a model falling on a rough tabletop surface, or a measuring tape snapping prematurely can all lead to paint chipping from your models.


However, at least those are situations we can understand. If you use your models, there is chance for wear and tear. That is what we expect with most things in life.

But your models being scratched while sitting in a carrying case is just disappointing. It's not even something that you can control. Foam just happens to be rough enough that friction can rub the paint off your models. This is especially so with points and edges, usually on weapons.

However, if you magnetize your models, you eliminate the chance for wear and tear of your models during transport entirely! There is no foam to rub the paint off your models. Also, sometimes models can come into contact with each other in a case. Friction between those models can cause chipping. That wont happen here either! The illustration to the left shows how strong a hold these magnets have. The tin can even be held upside down and shaken, and they still hold!

The best part is, all you need are strong magnets (rare earth) that are probably available at your hobby store, or various other random places (like Princess Auto), and hot glue to attach them to the bottom of your base. Then, the metal storage container can be acquired from anywhere. Danish Butter Cookie tins, metal lunchboxes, or even tins from the dollar store! You can add little flair by spray painting the tin, and adding in a stenciled Guild Ball logo on the lid. Kind of like what we did when putting the logo on our home-made mats from my previous article HERE.

But remember the story I mentioned about the guy with 5 or more different tins who precariously carried them to the hobby store? We can add some safety by putting the tins in a bag to carry. I bought a small lunch bag from the hardware store, sprayed it black, and added a Guild Ball logo to personalize it.




The official Guild Ball bag from BattleFoam is $74 USD. It's a great, high-quality product, but it only holds 2 trays of foam. This arrangement allows as many tins as you want (depending on the size of the bag you buy), and smaller models can even be magnetized upside down on the lid for even more storage space! This whole combination only cost me $15 Canadian, taxes included!

Now, there are some downsides to magnetizing. In theory, if you threw your Battlefoam bag, filled with miniatures, your models have some chance of not being too broken. With this layout, extreme force will likely cause the models to detach from their spots in the tins. This isn't so much of an issue for me, as I have been carrying models in cases for the last 20 years or so, and not once have I ever accidentally thrown a carrying case. I've dropped them from my hand, resulting in a 1-foot drop, maybe. But that shouldn't affect the magnetic hold of these models. Also, this process also adds extra cost and time to each model. If not done correctly, you may also have your models still move around when the case moves around. Make sure you do it correctly, or else it defeats the whole purpose of this method! Also, if you happen to use metal rings to mark AOE's (I'm looking at you, Alchemists), be warned: your models may move from their current positions on a table if the rings are placed too close to your models base. If you are OK with these concessions, then magnetizing your models may be right for you. It sure works out for me!

Enjoy the rest of your day! :)

P.S. Due to some input, I will write an article on how-to, and points to consider when magnetizing your models!

-the aY

Alchemists Spotlight - Midas Striker Team

Last week, I decided to trade in some Magic cards on a whim. Apparently, I had some cards that were worth some decent coin! With my spoils, I picked up the remaining two models of the Hunter's team (Seenah and Chaska) that I was missing, and the entirety of the Alchemist faction, minus Katalyst. I also got to pick up Decimate and Mist, so I can use them in my Mason's lineups.

After playing so much Butcher's, I thought I would like to play a Striker team, but not so obvious like the Fishermen. But, after looking at the cards of the Alchemists, combined with some Union model help, I thought it was very realistic to make a fast-paced, high-octane Alchemist team that could threaten the goal from multiple threat vectors.

I also happen to like the idea of playing super-solos that can do a lot themselves (I'm a fan of this playstyle in many games), so I thought the obvious choice would be 'King' Midas himself. The hobbyist side of me wanted to make my model look like he was actually performing some kind of field alchemy, so I took my regular cork bases and made something that was very Full Metal Alchemist-esque. If you don't know what that is, you owe it to yourself to watch that series! It's probably my favourite anime series of all time.

Back on topic: Midas is amazing. The whole GB community probably already knows that. He can be a beater if he needs to be, but I think his comfort zone is being zippy and scoring goals. If you can steal 'Where'd They Go?', then you are in for some amazing times. He is just so mobile, and he has so much defensive tech built in, he feels almost unstoppable. His only weakness is that he can only activate once a turn, really.

   So, with all this Midas threat that is always on the table, I knew I needed to add some more strikers to make it a Striker team. Vitriol is the obvious choice. A very mobile, accurate Striker, who also happens to be able to beat face if need be. Also, she happens to be debated among the community as a contender for "best Striker, non-captain" on the forums.

   I think under most circumstances, having a double striker list is probably enough to be considered a goal-oriented team, however I prefer threat saturation when we are going for skews. So, let's add a third Striker! Mist was the top candidate. Although they tend to have great kick stats across the board, the remaining Alchemists don't quite have the mobility to be true Strikers. Mist having Where'd They Go just gives him that extra mobility to get into good scoring positions, or get into a spot where a snap-kick is possible. While he is excellent, the lack of a momentous tackle generally means he can't be the first activation in a turn to score a goal. So beware!

   Rounding out the rest of the team, I put in Flask as the mascot based on community feedback, but Naja could work. After a first-turn cloud to help Vitriol, I just tend to leave the mascot by the goal to help act as a ghetto goaltender. Compound, I feel is an easy-include in any Alchemist list, just because he generates 2 Influence and can act most turns without any INF. Just having the Rush-keeper stops certain goal runs, and controls a large table area. The sixth spot is what is currently the slot I have yet to finalize. Decimate seems to be the natural choice with her good kick stat and mobility, plus her ability to generate momentum easily if required.

   When I play with this list, it just feels like I can play recklessly, make mistakes and bad trades, and still come out on top at the end of the game due to the high capability to score goals from multiple models on the team. It doesn't matter if you give your opponent 10 VPs because you aren't defending well, or accidentally give a way easy take-outs. As long as you get 12 VPs, you still win! If you are an alchemist player already and haven't tried playing this way, try it out! If you aren't an alchemist player, but are looking for a new team, I'd say this is a solid choice. I know it's not any news to say that Midas is awesome. But for those who have never played as Alchemists, you don't realize how FUN a list like this is to play until you try it!

Kicks for Kids Tournament Battle Report!

   Well, this will be my first ever battle report, for my first ever tournament in Guild Ball. It was a friendly tournament to help the Sick Kids Foundation, held at Meeplemart. Be sure to visit there to get some product, and play some games against some friendly people!

The battle report wont have every single detail, but I'll write as much as I can remember. It was too frantic to takes notes, as we were on Team Tactic's timing (45 minute death clocks, with 1-minute activation's after, giving up 1 VP when you end those turns).

My 8-man roster was:
-Fillet
-Princess
-Boiler
-Brisket
-Shank
-Rage
-Avarisse & Greede
-Tenderiser

I was seriously considering Ox going into this tournament, because I am much more familiar with him, but I really wanted to use my newly converted Fillet for the first time. That article showing how I made it can be found here. A+G was just there to meta against other A+G's. The rest of the team are pretty standard-fare for Butcher's teams.

Round 1- Jacob and the Alchemists. <Smoke, Flask, Vitriol, Hemlocke, Decimate, Compound.>
Jacob and I had a gentleman's agreement to not use Avarisse and Greede.

   The match started off with Vitriol going way up, and scoring a turn 1 goal. Unfortunately, she also ended up in a big forest that was on my side of the table buffing her, and making it harder for me to get at her. She was effectively locking down Brisket from efficiently getting the ball, and Shank was distracted by her too. At least Fillet now had the ball, so I could threaten the goal, and goad my opponent into coming closer to Fillet to try to get the ball. Smoke came up and used a combination of abilities to essentially put Poison on my whole team. My whole team through a variety of conditions, and attacks was down 3-5 damage. Very strong start for the Alchemists, I'd say. Alchemists 4, Butchers 0.

   The next round was a good one for me. In the previous round, Rage and Boiler had been able to put up some bleeds and reasonable damage on Decimate, and Smoke, and this turn, a very aggressive Hemlocke had tried to do some damage on one of my players. My fully-loaded Fillet charges into Decimate who has not yet activated (and has 4 INF) and does enough to get her down to 3 life before I legendary played to finish her off (and deal 3 damage to Smoke and Hemlocke). Fillet then finishes off a very wounded Hemlocke, and dodges into Smoke to finish her off. Alchemists 4, Butchers 6.

   The next round, I use my activation's to soak up the Gluttonous mass on Compound, apply bleed on him, and deal some small damage to Flask with Boiler and Shank. Smoke ends up retaliating by attacking Boiler, but he survived, and now three enemies are relatively close together, and all wounded. I weigh the options. I knew I needed to take-out one of them, and I could try scoring a goal to finish the game. I'd let the dice determine what I would do. Fillet goes in, and finishes off Smoke in only 2 hits. So, I thought if I still had 4 Influence, I may be better off trying to get the last 4 VP's by killing the remaining 2 models instead of hoping for 3 dice to get a 4+, and "wasting" 3 Influence. In the end, I decided to go for the take-outs. We kill off Compound who was at about 5 life or so, and we kill Flask. He explodes, and kills my Boiler.

But there we had it, Butcher's victory, 6 take-outs.
Since I wasn't hindered getting to the Alchemists, I was generating a ton of momentum. I was using a lot of  it to heal and remove various poison's off my players. I may have healed over 20 damage that game using Momentum.


Round 2 - Victoria and the Butcher's. <Fillet, Princess, Boiler, Brisket, Shank, Rage>
An exact mirror match, including our exact roster selection! Victoria was a newer player, so I tried to explain a few things as we played.

Both of us played quite conservatively at the beginning. We each moved our models up to the pitch cautiously, with my Brisket holding the ball. My intention was to have her and Shank move up the field to get some goals, while Fillet and friends took care of everyone else. I think Victoria was intending the same thing, and were on the same side as my pair. See? A true mirror match!

The next round, anyone is in range of anyone. Everyone on both our teams were probably in a big 8" circle on the field. One of us

was going to lose a model for sure this turn, and I wanted to make sure it wasn't my Fillet, so I start by putting Swift Stance on Fillet with Boiler and then applying a random Bleed to someone. Victoria responds with Rage going into my Shank, and doing some significant damage. Maybe in the lines of 10-12. I pretty much knew Shank was dead, and I decided I would let him die (even with 3 INF), and activated Rage to Tool Up Fillet and then Free charge her Fillet. I do around 4 damage on Fillet and more importantly, apply Bleed to her. Victoria, as expected, activates her Fillet to finish off Shank and deal some damage to my Fillet. But the 6+ defense keeps me from taking too much. I do a counter-attack at some point to do more damage to Fillet. So, I look at the table, and see that her big damage dealers have gone, and decide that Fillet can wait to activate. I activate Princess to get into melee with two of her models for gang-up potential with Fillet. She activates her Shank and does some damage to some people, but I am getting excited to activate Fillet.

Fillet's activation turn! She does damage to Victoria's Fillet, bringing her down to 2. I use my Legendary Play to finish her off, and deal damage to her Rage. Fillet then advances and kills both Rage and Shank. 3-kill activation again! The rest of the game boils down to my healing a lot, and then finishing off her wounded models that came back onto the pitch, while our Brisket's danced around each other to try and get the ball from each other. In the end, it's 12-2, 6 take-outs again.

 Round 3 - Sam and the Brewer's. <Esters, Scum, Hooper, Stave, Mash, Friday>
Once again, a gentleman's agreement to not use Avarisse and Greede. I have to be the kicker, so I choose the side that happened to have two obstructions in front of, and on either side of the goal. I felt this would be a good position to funnel my opponent in, and make it harder to get a clear goal. I decide to replace Brisket for Tenderiser.

I nominate Shank who is way off in the flank to be my kicker. Sam responds by putting most of his team on the left side of the table, but keeps Friday on the right to have his striker's out on either flank. Shank goes up and kicks the ball way on the other side. The scatter favoured me, and Friday was the only model able to actually retrieve the ball.

Hooper then goes up and far charges my Rage, leaving him knocked down, and on only 4 health. I respond with Boiler going in on Hooper, applying a Bleed and some damage, and healing Rage. Other stuff happens, but then Fillet comes in and wrecks Hooper, so I can have an early VP advantage. I see Sam measure out this HUGE range from Mash to my goal. He wanted to do some long-range goal scoring, probably involving teamwork plays, but my Tenderiser seemed to be deterring him from going through with it.

Throughout the game, Sam's dice conked out on him and he failed a few passes which would force him to use extra influence which messed up his activation's. Esters eventually came up to charge Rage (and Boiler) again, but he also flubbed some attack rolls, 2 of which netted 0 hits after armour. That left Esters open to be killed by Fillet and friends.
While all this was going on, Shank was on the top left of the field constantly harassing and stealing the ball and threatening the goal, causing my opponent to have to commit 2-3 players to try and beat him down and take the ball. However, counter-attack-dodges kept pesky Shank alive to harass some more!

Eventually, Shank tried to score a goal from the flank after stealing the ball, but it missed and ended up somewhere behind the goal. The current score was then 8 to 4, and it looks like we weren't going to score any more goals. My opponent tried to heal up a ton of damage to prevent easy take-out's. Both of us ran out of main clock time, and we alternated activation's, giving up a point each time. A new round began, I got to go first, and at 10 to 6, Fillet went in and finished off a wounded Hooper to finish the game.

The event concluded, and I was 3-0! I won a sweet Butcher's patch for best in-faction, and the rest of the prizes were distributed via raffle tickets. I got an extra ticket for being the 3-0, and got to win the only Butcher's model I don't own: Truffles! And a Hunter's patch for my wife! All in all, it was a great event, I met some new friends, and I got to experience games against teams and captains I've never played against. Fun times!

I know this wasn't really as in-depth, or detailed as some would like, but it's what I can remember off the top of my head without notes.

Hope you enjoyed it!

DIY Goal Post for Guild Ball - Pile of Gold

In Guild Ball, a lot of the personality of your team comes from having a custom Goal Post to represent the character of your team.

If you go to the main Guild Ball Forums, you can see all sorts of custom things people have done under "the Display Cabinet" sub forums. From there, you can get all sorts of inspiration.

Recently, I was inspired by my friend's Union Goal Post. Very appropriately, it was a large mound of coins. He told me the overall gist of how he did it, but I decided to revise the design a bit.

If you are interested in making something similar, here is the simple guide:

1- Use some kind of clay (or play-dough!) to make the base of the mound as pictured.

2- Stick random bits to add some character to it. I happened to have a sword and banner lying around.

3-After the clay hardens, reinforce it with glue (I used hot glue), prime it, and give the whole thing a base coat of paint.

4- Once it's all done, put on a watered-down layer of glue and use Gold Glitter. Fortunately, my glitter I bought at the dollar store is actually round, so if you look very closely, they actually look like coins.

5- Once dry, seal it in with another layer of watered-down glue, and there you have it!

I like this particular goal, because not only is it appropriate for the Union Guild, but because I put my moniker ("the aY", duh!), it is applicable to all my teams. Yes, I am very vain, it seems.

Hope you enjoyed this blog entry! :)

-the aY

Try converting a model! Guild Ball - Fillet: "a REAL Blood Dance"

Well, I know models and how "cool" they look can be a highly subjective thing. When it comes to Guild Ball models, I think they are overall very good, but sometimes they are missing a little something extra.

In the past, when I bought models, I assembled them as quick as I could, primed them, and painted them immediately. I didn't bother cleaning models, filling in gaps, or anything else like that. I didn't care at all about the hobby aspect. I just wanted them on the table so I could use them to play the game.

Overall, I am still like that. But I certainly clean the flash and mold lines off of all my models now. Filling in gaps is still something I don't care enough to do, but thankfully, the models today seem to be of higher casting quality than they used to be of yesteryear, so it's not something I ever feel I have to do. There just aren't as many gaps as there used to be.

 Back to Guild Ball. I feel like a lot of them are missing "something." Either they are too static, or they are just missing some kind of flair. I'm not a conversionist. I have done the occasional mod here and there, but I just don't have the time or care to do some of the crazy things I've seen people do with their models.

 However, it's Labour Day, and I am in a very, very rare situation in my life: I'm relatively unbusy today! Mind you, I still put up a floating shelf, did my grocery shopping, went on a walk with my family, and am hosting a BBQ for the in-laws. But I thought, "I have an hour or so... let's Make Fillet REALLY Blood Dance!"

So, my first conversion of any real substance that didn't involve just a head swap. Check it out! Sure, maybe it's very un-realistic. It's very anime-esque. But I just wanted my Fillet to have swirls of blood circling around her as she dances through and slices down her opponents. I think this accomplishes that look. :)

Hope you guys like it, and I hope it inspires other non-hobbyists to try something new with their models.
Have an amazing day!

-the aY